Turbobricks Forums

Turbobricks Forums (https://forums.turbobricks.com/index.php)
-   performance & modifications (https://forums.turbobricks.com/forumdisplay.php?f=13)
-   -   Need Assistance - Spacers/Hub Centric Adaptors for Fitting P1 wheels to 700 series (https://forums.turbobricks.com/showthread.php?t=362196)

lookforjoe 10-03-2021 08:07 AM

Need Assistance - Spacers/Hub Centric Adaptors for Fitting P1 wheels to 700 series
 
Searched, but didn't find definitive posts.

Just want to know what spacers/ hub centric adaptors are needed to fit P1 wheels to the live rear axle 745 wagon.

C30 wheels are 63.4 hub bore/ approx ET45-50 -

looking online 700's have 65.1 bore ET20 offset?

20/25mm spacers all around? Or less because the 17-18" wheels are all wider? I always get confuddled when it comes to calculating offset/width changes (most math, honestly)

Thanks in advance

AndrewNance 10-03-2021 11:18 AM

https://www.willtheyfit.com

I like to use this so you get a visual of how the new wheel/tire will sit in comparison to the current one.

Redwood Chair 10-03-2021 11:37 AM

700 wheels are 25et except for the multi-X which are 20et.

blkaplan 10-04-2021 11:09 AM

You would want something in the 25-32 range

lookforjoe 10-06-2021 08:06 AM

Quote:

Originally Posted by blkaplan (Post 6220177)
You would want something in the 25-32 range

Hey Ben - Does BNE machine spacers with the necessary hubcentric lip for matching the desired wheel? In other words, can you make them as needed, or do they only come in certain configurations?

blkaplan 10-06-2021 12:46 PM

Quote:

Originally Posted by lookforjoe (Post 6220884)
Hey Ben - Does BNE machine spacers with the necessary hubcentric lip for matching the desired wheel? In other words, can you make them as needed, or do they only come in certain configurations?

We could probably modify a set here to have the requested CB on the wheel side. We try to stay away from customs though

lookforjoe 10-07-2021 12:58 PM

Quote:

Originally Posted by blkaplan (Post 6220950)
We could probably modify a set here to have the requested CB on the wheel side. We try to stay away from customs though

Understood. I'll have to check the CB on the actual wheels (Enkei, Advanti) & see if that matches anything you already do. I can find yours easily on the site, or are they hiding? :)

blkaplan 10-07-2021 02:57 PM

Quote:

Originally Posted by lookforjoe (Post 6221252)
Understood. I'll have to check the CB on the actual wheels (Enkei, Advanti) & see if that matches anything you already do. I can find yours easily on the site, or are they hiding? :)

Hope they are easy. Can always shoot me an email to get it sorted.

AnthonyHardy2 10-17-2021 02:59 AM

Also make sure you check the size of the lugnut holes. If they're the same as V50 wheels which are also P1s you may need to use the original lugnuts. I ran Clavas (16x6.5) from a V50 on my 242 and later on a 940SE for awhile and the lugnut holes were much larger than on any other wheel I've seen. My stock 240 lugnuts pulled straight through the holes and the aftermarket lugnuts I ordered with decent sized shoulders were still too small.

Marvelous3 10-17-2021 07:55 PM

Buy the propus c’s in for sale section.
Buy a set of Ben’s extended studs and 25mm spacers.
Install is easy.
Bolt wheels on.
Happy day.

Alex Buchka 10-17-2021 08:37 PM

https://forums.turbobricks.com/showthread.php?t=360090

I got what you need.

lookforjoe 10-18-2021 09:17 PM

Quote:

Originally Posted by Alex Buchka (Post 6223488)

Alex - what wheels would need 40mm spacing?

Alex Buchka 10-19-2021 02:21 AM

Quote:

Originally Posted by lookforjoe (Post 6223721)
Alex - what wheels would need 40mm spacing?

I don't know specifically. I ran them on a 240 with a set of V50 wheels.


All times are GMT -4. The time now is 11:31 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.