Search results

I am not. I'm talking about a map of an engines Volumetric efficiency (not a fuel VE table either. Similar to a compressor maps in the sense that it gives you an understanding over the rev/load range how efficient your engine is. Realistically this is different for every single setup. But I was...

I'll definitely check out xona rotors though.

Definitely looking into joshes cakes because of their ability to push that long. I think he lists out to 7500 and higher on his website. I just figured I may do a little more research on cams before I commit. But he seems to have good reliability and good over power band from them. And I was...

Well obviously 😂 not planning on the engine taking a dump. Goal is 450 to the wheels. But I am realistic and willing to compromise peak power for a better power band. Stock pistons and crank will hold plenty of power, but definitely doing h-beam rods, my current personal debate is just doing...

Another reason I was really looking for any *cough cough* similar setups. I still haven't made a Decision on turbo manifold, and still haven't made a decision on intake. Maybe the KL racing intake, but may also just fabricate one depending on fitment etc. But yeah I know no one's gonna have an...

Ok I see where you're going with this. That wouldn't be a bad idea. Only problem for me is I'm still in the machining phase. Then still have engine assembly. I have an in house engine dyno at my job and gonna run the engine na for a break-in session or two on the dyno. Prior to fitting into the...

Not VE fuel map as I stated above. Im looking for a VE map as in the VE of the engine, in it's ability to pump air/fuel in and exhaust out. Not the same as a VE fuel map. I do thank you for your input though.

Hey guys I'm in the process of building/planning my turbo motor build. It is going on my race car for time attack and other circuit racing. I'm in the process of deciding what turbo I would like for my build. I am wondering if anyone out there has a Volumetric efficiency map for a b230ft bottom...

Hey guys I'm in the process of building/planning my turbo motor build. It is going on my race car for time attack and other circuit racing. I'm in the process of deciding what turbo I would like for my build. I am wondering if anyone out there has a Volumetric efficiency map for a b230ft bottom...

Anyone know if the cam caps are any different between the 530 and 531 heads? I picked up a 531 cheap, but it is missing caps. I know I'd have to have things line honed, but could I just buy can caps for any 8v head?

Hey guys, been a while since I posted but here I go. BTW my car is a 92 240 with LH2.4 So my AW70 finally **** the bed some months back so I decided it was finally time to manual swap. Job is basically near completion, but I cant seem to start the vehicle. No spark, No injector pulse. My...

Hey guys both the engine mounts on my 240 **** the bed at about the same time (they were bad for a while and i was putting them off to fix other stuff,BUT) they are now both sheered completly only gravity holding them in place so I purchased some yoshifab ones since it'll be a perfect time to...

Hey guys, i know that the best way to fine tune my lh2.4 system is to use the ostrich emmulator. But if i just have an upgraded chip and wanna stay that way for a bit, whats the best way to fine tune with a wideband watching afr's??? Using an ajustable FPR? BTW for some reason i cant access the...

Hey guys, ive been searching my a** off trying to find a catless midpipe for a volvo 240. Any idea if anyone makes ready to buy? Or do i have to buy a cat pipe and cut the cat put and weld in a pipe? I would just rather not pay for a cat if i dont have to.

Hey guys, after trying to research and having all answers point to RSI (who doesnt seem to be in business anymore) where can i buy larger valves for a 531 head im trying to build?

Hey guys continuing my research before i start accumulating parts for my +T. I have a 92 240, ive heard that when you +T ypy dont want to use the 240 turbo injectors cause the impedence is different. Is tths true? Which injectors should i get? Thanks in advance guys. P.s. i have searched but...

Hey guys. Ive currently got a 92 240 with 2.4lh that im currently trying to get to stage 0 before doong any power adders. Now i come from the audi vw world and am learning this car as i go. But i have a question. Im looking at doing a full tune up soon and am thinking about throwing a Crane PS60...