• Hello Guest, welcome to the initial stages of our new platform!
    You can find some additional information about where we are in the process of migrating the board and setting up our new software here

    Thank you for being a part of our community!

Search results

  1. S

    B230 redblock coolant pressure in hoses??

    My b230 reblock running 20psi running composite type head gasket my question is the water hose seem to have some pressure in them should the have next to no pressure or is it normal for them to have pressure
  2. S

    Trw steering rack movement in pinion

    My 940 has Trw steering rack the is knocking and movement in pinion would this be the bearing in the pinion? I can't find and proper rebuild kits or even the bearings sizes. Thanks for any help
  3. S

    Budget 350hp b230fk build (9.3:1 compression)

    Hello Did you ever get finished
  4. S

    940 Electric fan will it work when aircon disabled?

    My 1997 940 engine fan doesn't seem to be working. It dose work when I disconnected the temperature sensor I changed the sensor but unsure if it was a good one.the aircon is removed and the aircon sensors and all disconnected would this make a difference
  5. S

    Ocean classic wheel still available?

    I did check in Europe all I seen were out of stock
  6. S

    Ocean classic wheel still available?

    Are Ocean classic wheel still available?
  7. S

    Boost in second gear

    Big man behind a keyboard 🤣
  8. S

    Boost in second gear

    You never know what people's going through in life I try to help people when I can not be useless and hurtful
  9. S

    Boost in second gear

    I've had a t3 turbo fitted and now a holset 3rd 4th ans 5th boost come in nice and early but in second gear it's very close to redline what can I do to improve this
  10. S

    Holset 351 fit with standard manifold

    Will a Holset 351 physically fit with standard manifold in a 940
  11. S

    Do you rev your redblock to redline

    I want to use my b230 8v for drifting/road you need to rev the car more to redline what camshaft would you use that's happy for full rev range. My car has a cam that I'm unsure of the spec, I have chipped ecu,blue injectors T3 turbo upgraded fuel pump 3inch maf , steel rods full 3inch...
  12. S

    most power on standard 530 head

    What is the most power a standard 530 head with cam turbo ect to suit will make when dose the head limit the power
  13. S

    2mm redblock headgasket

    Got the car back running thanks for the help
  14. S

    2mm redblock headgasket

    What about the valve clearance
  15. S

    2mm redblock headgasket

    The inlet valve when fully open is .64mm below head surface The exhaust valve when fully open is .92mm below head surface
  16. S

    2mm redblock headgasket

    The mesure were from the machine shop I remeasure today Cylinder head measurements from rocker cover mount to head gasket surfaces Is 145.11mm Piston stick out is .60 mm I have a 1.8mm when tightened head gasket
  17. S

    2mm redblock headgasket

    I checked the piston is .60mm above the block I have a 1.8 mm gasket could I fit this
  18. S

    2mm redblock headgasket

    .09 + .4 = .49 was removed total of head .254 was removed from the block
  19. S

    2mm redblock headgasket

    T The head was skimmed twice
  20. S

    2mm redblock headgasket

    Turbo motor I checked it before I over heated the engine to leave it back to standard I used a 1.5mm head gasket It was skimed again .4 so I need a 1.9mm gasket
Back
Top